3000ta有机硅涂层胶生产企业的总平面图设计

论文编号:CL081  论文字数:10199,页数:25

摘 要：有机硅涂层胶具有良好的阻燃性和热稳定性，他可以增强涂层强度、弹性，也可降低摩擦系数。有机硅涂层胶具有较好的渗透性、热稳定性好、表面张力低、平滑性佳、橡胶弹性和通气透湿性优良、对皮肤无刺激等特点,所以它是一种应用广泛,前景光明的纺织助剂。自从20世纪70年代以来，有机硅涂层胶在国内外迅速发展，产品性能也越来越稳定，工艺路线日趋完善，所以我们根据目前有机硅涂层胶工艺，进行此产品的工厂设计，而我所负责的是3000t/a有机硅涂层胶生产的总平面图设计。设计的内容包括行政和研发中心，生产车间的设计，仓库的设计，消防中心的设计及一些辅助设备的设计，设计采用的依据GB 50187-93和GB50016-2006.
关键词：有机硅涂层胶、总平面图、设计。

Abstract: Silicone coating adhesive has good resistance and thermal stability, he can enhance strength, elasticity, coating can reduce the friction coefficient. Silicone coating adhesive has good permeability, good thermal stability, low, smooth the surface tension, rubber permeability good elasticity and ventilation, no stimulation to the skin etc, so it is a kind of wide application prospects of light, the textile auxiliaries. Since l970s, silicone coating adhesive products at home and abroad and rapid development, more and more stable performance, technology route has been improved, so we according to the current organic silicon coated adhesive products factory, the design, but I was responsible for the organic silicon introduces/a total floor coating adhesive production design.
Keywords：Silicone coating adhesive；general plan；design.

目  录
中文摘要 I
英文摘要 II
目录 III
1. 绪论 1
 1.1 有机硅涂层胶的概述...........................................1
 1.2 本课题的提出.................................................2
2.基本概况...........................................................2
 2.1 项目产品、物化性质及用途.....................................3
 2.1.1  有机硅涂层胶简介......................................3
 2. 2 工艺技术方案................................................3
           2.2.1生产工艺及物料平衡................... 3
           2.2.2 原辅料性质及用量.................... 3
           2.2.3主要设备................................4
           2.2.4主要建筑..............................4
           2.2.5全厂定员...............................5
      2.3 投资概算...........................5
      2.4 建设选址、用地与相关规划......... ............................6
      2.5 资源利用和能源耗用分析......... .........6
      2.6 生态环境影响分析......... ............6
3. 设计部分 8
 3.1 厂区平面图 8
 3.1.1 总体布局 10
 3.1.2 布置理念 11
 3.1.3 各区域集中布置........ ........ ........ ...............11
 3.2 行政中心和研发中心的设计 12
 3.3仓库的设计.................................................. 13
  3.4生产区的设计................................................15
  3.5甲类灌区的设计..............................................16
  3.6 污水处理区设计.............................................16
  3.7 消防设计...................................................16
      3.7.1 设计依据.............................................16
      3.7.2 事故发生可能性及危险性分析...........................16
      3.7.3 燃烧爆炸的原因.......................................17
      3.7.4 消防安全措施.........................................17
                3.7.5 消防系统............................................18
          4．总结与展望.......................................................19
致谢................................................................20
参考文献............................................................21